Fountainhead Alloys
Opera House, Mumbai, Maharashtra
GST No. 27AKOPC9787G1ZI
TrustSEAL Verified
Call 08047643051 89% Response Rate
SEND EMAIL
Product Details:
| Minimum Order Quantity | 50 Kg |
| Material | Aluminum Alloy |
| Usage/Application | Construction |
| Brand | FHA |
| Length | 100 m |
| Packaging Type | Roll |
| Grade | Al 7039 |
| Standard | D74S 74530 |
Aluminium / aluminum is one of the lightest available commercial metals with a density approximately one-third that of steel or copper. It can be easily fabricated into many forms such as foil, sheets, rod, tube, geometric shapes, and wire.
Aluminium / aluminum 7039 alloy is a heat treatable wrought alloy. The following datasheet will provide more details about aluminium / aluminum 7039 alloy.
The following table shows the chemical composition of aluminium / aluminum 7039 alloy.
| Element | Content (%) |
|---|---|
| Zinc, Zn | 3.5 - 4.5 |
| Magnesium, Mg | 2.3 - 3.3 |
| Silicon, Si | 0.3 max |
| Iron, Fe | 0.4 max |
| Chromium, Cr | 0.15 - 0.25 |
| Manganese, Mn | 0.1 - 0.4 |
| Copper, Cu | 0.1 max |
| Titanium, Ti | 0.1 max |
| Remainder (total) | 0.15 max |
| Aluminum, Al | Remainder |
The physical properties of aluminium / aluminum 7039 alloy are outlined in the following table.
| Properties | Metric | Imperial |
|---|---|---|
| Density | 2.74 g/cm³ | 0.0990 lb/in³ |
| Melting point | 482-638°C | 900-1180 °F |
The mechanical properties of aluminium / aluminum 7039-T64 alloy are tabulated below.
Wire Gauge (SWG):
Certification:
| Properties | Metric | Imperial |
|---|---|---|
| Tensile strength (@diameter 12.7 mm/0.500 in) | 450 MPa | 65300 psi |
| Yield strength (@diameter 12.7 mm/0.500 in) | 380 MPa | 55100 psi |
| Elongation at break (@diameter 12.7 mm/0.500 in) | 13% | 13% |
| Elastic modulus | 69.6 GPa | 10100 ksi |
| Shear strength | 255 MPa | 37000 psi |
| Hardness, Brinell (@load 500 kg; thickness 10.0 mm/1100 lb;0.394 in) | 133 | 133 |
| Hardness, Knoop (converted from Brinell hardness value) | 167 | 167 |
| Hardness, Rockwell A (converted from Brinell hardness value) | 50 | 50 |
| Hardness, Rockwell B (converted from brinell hardness value) | 81 | 81 |
| Hardness, Vickers (converted from Brinell hardness value) | 153 | 153 |
Product Details:
| Minimum Order Quantity | 50 Kilogram |
| Material | Aluminum Alloy |
| Usage/Application | Construction |
| Brand | FHA |
| Shape | Round |
| Length | 500 m |
| Packaging Type | Roll |
| Grade | Al 6063 63400 H9 Al-Mg-Si 0.5 |
Aluminium alloy 6063 is a medium strength alloy commonly referred to as an architectural alloy. It is normally used in intricate extrusions.
It has a good surface finish, high corrosion resistance, is readily suited to welding and can be easily anodised. Most commonly available as T6 temper, in the T4 condition it has good formability.
Aluminium alloy 6063 is used in:
In balustrading the rails and posts are normally in the T6 temper and formed elbows and bends are T4. T4 temper 6063 aluminium is also finding applications in hydroformed tube for chassis.
Aluminium alloy 6063/6063A also corresponds to the following standard designations and specifications:
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Chemical composition for aluminium alloy 6063 and 6063A
| Element | 6063 % Present | 6063A % Present |
|---|---|---|
| Si | 0.2 to 0.6 | 0.3 to 0.6 |
| Fe | 0.0 to 0.35 | 0.15 to 0.35 |
| Cu | 0.0 to 0.1 | 0.1 |
| Mn | 0.0 to 0.1 | 0.15 |
| Mg | 0.45 to 0.9 | 0.6 to 0.9 |
| Zn | 0.0 to 0.1 | 0.0 to 0.15 |
| Ti | 0.0 to 0.1 | 0.1 |
| Cr | 0.1 max | 0.05 |
| Al | Balance | Balance |
The most common tempers for 6063 aluminium are:
Product Details:
| Unit Length | 12 m |
| Material | Aluminum Alloy |
| Usage/Application | Chemical Handling |
| Grade | Al 6061 65032 H20 Al-Mg-Si Cu |
| Size/Diameter | 500 mm |
| Shape | Round |
| Surface Finish | Finished Polished, Anodized, Brushed, Mill Finished |
| End | Plain End |
| Brand | FHA |
Aluminium alloy 6061 is one of the most extensively used of the 6000 series aluminium alloys. It is a versatile heat treatable extruded alloy with medium to high strength capabilities.
Composition:
Typical composition of aluminium alloy 6061
|
Component |
Amount (wt.%) |
|
Aluminium |
Balance |
|
Magnesium |
0.8-1.2 |
|
Silicon |
0.4 – 0.8 |
|
Iron |
Max. 0.7 |
|
Copper |
0.15-0.40 |
|
Zinc |
Max. 0.25 |
|
Titanium |
Max. 0.15 |
|
Manganese |
Max. 0.15 |
|
Chromium |
0.04-0.35 |
Physical Properties:
Mechanical Properties:
|
Temper |
Ultimate Tensile Strength (MPa) |
0.2% Proof Stress (MPa) |
Brinell Hardness (500kg load, 10mm ball) |
Elongation 50mm dia (%) |
|
0 |
110-152 |
65-110 |
30-33 |
14-16 |
|
T1 |
180 |
95-96 |
16 |
|
|
T4 |
179 min |
110 min |
||
|
T6 |
260-310 |
240-276 |
95-97 |
9-13 |
Thermal Properties:
Product Details:
| Minimum Order Quantity | 50 Kilogram |
| Shape | Rectangular |
| Thickness | 50 mm |
| Material Grade | Al 6351 64430 H30 Al-Mg-Si1 B51S |
| Brand | FHA |
| Tolerance | -0.00mm/+5.00mm |
| Finish | Bright Smooth Finish |
| Material | Aluminum Alloy |
| Standard | UNS A96351,ASTM B221 |
Aluminum alloys tend to lose their strength when they are exposed to temperatures of about 200-250°C. However, their strength increases at subzero temperatures. They have high corrosion resistance.
The following datasheet will discuss in detail about the aluminum 6351 alloy.
The chemical composition of the aluminum 6351 alloy is tabulated below.
| Element | Content (%) |
|---|---|
| Aluminum, Al | 97.8 |
| Silicon, Si | 1 |
| Manganese, Mn | 0.6 |
| Magnesium, Mg | 0.6 |
The following table shows the physical properties of the aluminum 6351 alloy.
| Properties | Metric | Imperial |
|---|---|---|
| Density | 2.6-2.8 g/cc | 0.0939- 0.101 lb/in3 |
The mechanical properties of the aluminum 6351 alloy are outlined in the following table.
| Properties | Metric | Imperial |
|---|---|---|
| Tensile strength | 250 MPa | 36260 psi |
| Yield strength | 150 MPa | 21756 psi |
| Shear strength | 200 MPa | 29008 psi |
| Fatigue strength | 90 MPa | 13054 psi |
| Elastic modulus | 70-80 GPa | 10153-11603 ksi |
| Poisson's ratio | 0.033 | 0.033 |
| Elongation | 20% | 20% |
| Hardness | 95 | 95 |
Product Details:
| Minimum Order Quantity | 50 Kilogram |
| Material | Aluminum Alloy |
| Usage/Application | Construction |
| Brand | FHA |
| Length | 100 m |
| Form | Wire |
| Packaging Type | Roll |
| Grade | Al 6201 64401 |
Aluminum alloys are known for their strong corrosion resistance. They are sensitive to high temperatures ranging between 200 and 250°C (392 and 482°F). However, the strength of Aluminium / Aluminum alloys can be enhanced at subzero temperatures, thus making them perfect low-temperature alloys.
Aluminium / Aluminum 6201 alloy is a wrought alloy type. The following datasheet will provide more details about Aluminium / Aluminum 6201 alloy.
The following table shows the chemical composition of Aluminium / Aluminum 6201 alloy.
| Element | Content (%) |
|---|---|
| Aluminum, Al | 98.5 |
| Magnesium, Mg | 0.80 |
| Silicon, Si | 0.70 |
The physical properties of Aluminium / Aluminum 6201 alloy are outlined in the following table.
| Properties | Metric | Imperial |
|---|---|---|
| Density | 2.6-2.8 g/cm3 | 0.0939-0.1011 lb/in³ |
The mechanical properties of Aluminium / Aluminum 6201 alloy are tabulated below.
| Properties | Metric | Imperial |
|---|---|---|
| Elastic modulus | 70-80 GPa | 10152-11603 ksi |
| Poisson’s ratio | 0.33 | 0.33 |
Product Details:
| Minimum Order Quantity | 50 Kilogram |
| Wall Thickness | 5 mm |
| Material | Aluminum Alloys |
| Usage/Application | Chemical Handling |
| Size | 4 inch |
| Shape | Round |
| Surface Finish | Finished Polished |
| Grade | Al 6063 63400 H9 Al-Mg-Si 0.5 |
Aluminium alloy 6063 is a medium strength alloy commonly referred to as an architectural alloy. It is normally used in intricate extrusions.
It has a good surface finish, high corrosion resistance, is readily suited to welding and can be easily anodised. Most commonly available as T6 temper, in the T4 condition it has good formability.
Applications of 6063 AluminiumAluminium alloy 6063 is used in:
In balustrading the rails and posts are normally in the T6 temper and formed elbows and bends are T4. T4 temper 6063 aluminium is also finding applications in hydroformed tube for chassis.
Alloy DesignationsAluminium alloy 6063/6063A also corresponds to the following standard designations and specifications:
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Table 1. Chemical composition for aluminium alloy 6063 and 6063A
| Element | 6063 % Present | 6063A % Present |
|---|---|---|
| Si | 0.2 to 0.6 | 0.3 to 0.6 |
| Fe | 0.0 to 0.35 | 0.15 to 0.35 |
| Cu | 0.0 to 0.1 | 0.1 |
| Mn | 0.0 to 0.1 | 0.15 |
| Mg | 0.45 to 0.9 | 0.6 to 0.9 |
| Zn | 0.0 to 0.1 | 0.0 to 0.15 |
| Ti | 0.0 to 0.1 | 0.1 |
| Cr | 0.1 max | 0.05 |
| Al | Balance | Balance |
The most common tempers for 6063 aluminium are:
Product Details:
| Minimum Order Quantity | 50 Kilogram |
| Material | Aluminum Alloy |
| Usage/Application | Construction |
| Brand | FHA |
| Shape | Round |
| Length | 100 m |
| Packaging Type | Roll |
| Grade | Al 6061 65032 H20 Al-Mg-Si Cu |
Aluminium alloy 6061 is one of the most extensively used of the 6000 series aluminium alloys. It is a versatile heat treatable extruded alloy with medium to high strength capabilities.
|
Component |
Amount (wt.%) |
|
Aluminium |
Balance |
|
Magnesium |
0.8-1.2 |
|
Silicon |
0.4 – 0.8 |
|
Iron |
Max. 0.7 |
|
Copper |
0.15-0.40 |
|
Zinc |
Max. 0.25 |
|
Titanium |
Max. 0.15 |
|
Manganese |
Max. 0.15 |
|
Chromium |
0.04-0.35 |
|
Others |
0.05 |
|
Temper |
Ultimate Tensile Strength (MPa) |
0.2% Proof Stress (MPa) |
Brinell Hardness (500kg load, 10mm ball) |
Elongation 50mm dia (%) |
|
0 |
110-152 |
65-110 |
30-33 |
14-16 |
|
T1 |
180 |
95-96 |
|
16 |
|
T4 |
179 min |
110 min |
|
|
|
T6 |
260-310 |
240-276 |
95-97 |
9-13 |
Product Details:
| Minimum Order Quantity | 50 Kilogram |
| Material | Aluminum Alloy |
| Usage/Application | Construction |
| Brand | FHA |
| Shape | Round |
| Length | 100 m |
| Packaging Type | Roll |
| Grade | Al 6351 64430 H30 Al-Mg-Si 1 B51S |
Aluminum alloys tend to lose their strength when they are exposed to temperatures of about 200-250°C. However, their strength increases at subzero temperatures. They have high corrosion resistance.
The following datasheet will discuss in detail about the aluminum 6351 alloy.
The chemical composition of the aluminum 6351 alloy is tabulated below.
| Element | Content (%) |
|---|---|
| Aluminum, Al | 97.8 |
| Silicon, Si | 1 |
| Manganese, Mn | 0.6 |
| Magnesium, Mg | 0.6 |
The following table shows the physical properties of the aluminum 6351 alloy.
| Properties | Metric | Imperial |
|---|---|---|
| Density | 2.6-2.8 g/cc | 0.0939- 0.101 lb/in3 |
The mechanical properties of the aluminum 6351 alloy are outlined in the following table.
| Properties | Metric | Imperial |
|---|---|---|
| Tensile strength | 250 MPa | 36260 psi |
| Yield strength | 150 MPa | 21756 psi |
| Shear strength | 200 MPa | 29008 psi |
| Fatigue strength | 90 MPa | 13054 psi |
| Elastic modulus | 70-80 GPa | 10153-11603 ksi |
| Poisson's ratio | 0.033 | 0.033 |
| Elongation | 20% | 20% |
| Hardness | 95 | 95 |
Product Details:
| Minimum Order Quantity | 50 Kilogram |
| Material | Aluminum Alloy |
| Grade | Al 6061 65032 H20 Al-Mg-Si Cu |
| Usage/Application | Construction |
| Brand | FHA |
| Surface Treatment | Coated |
| Length | 18 meter |
| Diameter | 350 mm |
|
Component |
Amount (wt.%) |
|
Aluminium |
Balance |
|
Magnesium |
0.8-1.2 |
|
Silicon |
0.4 – 0.8 |
|
Iron |
Max. 0.7 |
|
Copper |
0.15-0.40 |
|
Zinc |
Max. 0.25 |
|
Titanium |
Max. 0.15 |
|
Manganese |
Max. 0.15 |
|
Chromium |
0.04-0.35 |
|
Others |
0.05 |
|
Temper |
Ultimate Tensile Strength (MPa) |
0.2% Proof Stress (MPa) |
Brinell Hardness (500kg load, 10mm ball) |
Elongation 50mm dia (%) |
|
0 |
110-152 |
65-110 |
30-33 |
14-16 |
|
T1 |
180 |
95-96 |
|
16 |
|
T4 |
179 min |
110 min |
|
|
|
T6 |
260-310 |
240-276 |
95-97 |
9-13 |
Thermal Properties: