Alloy code | |
1xxx Series | |
2xxx Series | |
3xxx Series | |
4xxx Series | |
5xxx Series | The alloying element is magnesium. Alloys of this series are moderate in strength (200 – 350 MPa). The strength is achieved by the heat treatment processing or forming. Alloys of this series have excellent resistance to corrosion in aggressive atmosphere and seawater. |
6xxx Series | The alloying elements are magnesium and silicon. Alloys of this series are moderate in strength (200 – 350 MPa). The strength is achieved by the heat treatment processing or forming. Alloys of 6xxx series can be easily anodized. |
7xxx Series | The alloying element is zinc. Alloys of this series have the highest strength among all series. The tensile strengths ranging between 450 – 500 MPa may exceed 600 MPa in some cases. These alloys prone to stress corrosion, especially when welded. |
8xxx Series | The alloying element is other than for the other series (including lithium). |
Product Details:
Minimum Order Quantity | 50 Kilogram |
Material | Aluminum Alloy |
Usage/Application | Construction |
Brand | FHA |
Length | 100 m |
Form | Wire |
Packaging Type | Roll |
Grade | Al 6005 62400 C51S |
Aluminium alloy 6005i s a medium strength, heat treatable alloy with excellent corrosion resistance.
Alloy 6005 has properties between those of alloys 6061 and 6082 and can sometimes be used interchangeably with these alloys but 6005/6005A has better extrusion characteristics. It has a better mill surface finish, but it is difficult to produce thin-wall complicated shapes in 6005/6005A. 6005 has very good bending properties.
Chemical Composition:
Chemical composition for aluminium alloy 6005
Element |
% Present |
Si |
0.5-0.9 |
Fe |
0.0-0.35 |
Cu |
0.0-0.3 |
Mn |
0.0-0.5 |
Mg |
0.4-0.7 |
Zn |
0.0-0.2 |
Ti |
0.0-0.1 |
Cr |
0.0-0.3 |
Mn+Cr |
0.12-0.5 |
Al |
Balance |
Mechanical Properties:
Mechanical properties for aluminium alloy 6005 T6
BS EN 755-2:2008 |
|
Property |
Value |
Proof Stress |
225 Min MPa |
Tensile Strength |
270 Min MPa |
Elongation A50 mm |
8 % |
Shear Strength |
205 MPa |
Hardness Brinell |
90 HB |
Elongation A |
10 Min % |
Product Details:
Minimum Order Quantity | 50 Kilogram |
Shape | Round |
Usage/Application | Construction |
Material | Aluminum Alloy |
Grade | Al 7039 D74S 74530 |
Single Piece Length | 6 meter |
Brand | FHA |
Diameter | 350 mm |
Aluminium / aluminum is one of the lightest available commercial metals with a density approximately one-third that of steel or copper. It can be easily fabricated into many forms such as foil, sheets, rod, tube, geometric shapes, and wire.
Aluminium / aluminum 7039 alloy is a heat treatable wrought alloy. The following datasheet will provide more details about aluminium / aluminum 7039 alloy.
The following table shows the chemical composition of aluminium / aluminum 7039 alloy.
Element | Content (%) |
---|---|
Zinc, Zn | 3.5 - 4.5 |
Magnesium, Mg | 2.3 - 3.3 |
Silicon, Si | 0.3 max |
Iron, Fe | 0.4 max |
Chromium, Cr | 0.15 - 0.25 |
Manganese, Mn | 0.1 - 0.4 |
Copper, Cu | 0.1 max |
Titanium, Ti | 0.1 max |
Remainder (total) | 0.15 max |
Aluminum, Al | Remainder |
The physical properties of aluminium / aluminum 7039 alloy are outlined in the following table.
Properties | Metric | Imperial |
---|---|---|
Density | 2.74 g/cm³ | 0.0990 lb/in³ |
Melting point | 482-638°C | 900-1180 °F |
The mechanical properties of aluminium / aluminum 7039-T64 alloy are tabulated below.
Properties | Metric | Imperial |
---|---|---|
Tensile strength (@diameter 12.7 mm/0.500 in) | 450 MPa | 65300 psi |
Yield strength (@diameter 12.7 mm/0.500 in) | 380 MPa | 55100 psi |
Elongation at break (@diameter 12.7 mm/0.500 in) | 13% | 13% |
Elastic modulus | 69.6 GPa | 10100 ksi |
Shear strength | 255 MPa | 37000 psi |
Hardness, Brinell (@load 500 kg; thickness 10.0 mm/1100 lb;0.394 in) | 133 | 133 |
Hardness, Knoop (converted from Brinell hardness value) | 167 | 167 |
Hardness, Rockwell A (converted from Brinell hardness value) | 50 | 50 |
Hardness, Rockwell B (converted from brinell hardness value) | 81 | 81 |
Hardness, Vickers (converted from Brinell hardness value) | 153 | 153 |
Product Details:
Minimum Order Quantity | 50 Kilogram |
Grade | Al 5005 |
Usage/Application | Construction |
Brand | FHA |
Material | Aluminum |
Length | 18 meter |
Diameter | 350 mm |
Aluminium alloy 5005 contains nominally 0.8% magnesium. It has medium strength, good weldability, and good corrosion resistance in marine atmospheres. It also has the low density and excellent thermal conductivity common to all aluminium alloys. It is the most commonly used grade of aluminium in sheet and plate form.
Aluminium alloy 5005 is a lean aluminium magnesium alloy which can be hardened by cold work: it is not heat treatable to higher strength.
Austral Wright Metals can supply this alloy as plate, sheet and strip. See Austral Wright Metals Catalogue for normal stock sizes and tempers.
Corrosion Resistance 5005 has the same high resistance to general corrosion as other non heat treatable aluminium alloys. It also has the higher resistance to slightly alkaline conditions common to the 5000 series alloys. The atmospheric corrosion resistance of 5005 is similar to that of 3003.
When anodised to improve corrosion resistance, the film on 5005 is clearer than on 3003, and gives better colour match with 6063 architectural extrusions.
The corrosion resistance of aluminium alloys relies on a protective surface oxide film, which when damaged is readily repaired by the rapid reaction between aluminium and oxygen. However, the high reactivity of the base metal can give rapid corrosion if the film cannot be repaired, so aluminium alloys are not suitable for use with reducing media.
Since aluminium is a reactive metal, it may corrode more quickly when in electrical contact with most other metals. The prediction of galvanic corrosion is complex, please consult Austral Wright Metals for specific advice.
Typical Applications of aluminium alloy 5005 include:
Chemical composition of Aluminium 5005.
Element |
% |
Element |
% |
Aluminium |
Balance |
Manganese |
0.20 max |
Magnesium |
0.50 – 1.10 |
Chromium |
0.10 max |
Silicon |
0.30max |
Zinc |
0.25 max |
Iron |
0.07 max |
Others, each |
0.05 max |
Copper |
0.20 max |
Others, total |
0.15 max |
Product Details:
Material | Aluminum Alloys |
Color | Silver |
Material Grade | Al 6061 Al-Mg-Si Cu |
Length | 6000 mm |
Thickness | 50 mm |
Finish | Bright |
Brand | FHA |
Application | Construction |
Aluminium alloy 6061 is one of the most extensively used of the 6000 series aluminium alloys. It is a versatile heat treatable extruded alloy with medium to high strength capabilities.
Typical composition of aluminium alloy 6061
Component |
Amount (wt.%) |
Aluminium |
Balance |
Magnesium |
0.8-1.2 |
Silicon |
0.4 – 0.8 |
Iron |
Max. 0.7 |
Copper |
0.15-0.40 |
Zinc |
Max. 0.25 |
Titanium |
Max. 0.15 |
Manganese |
Max. 0.15 |
Chromium |
0.04-0.35 |
Others |
0.05 |
Key Features:
Typical properties of aluminium alloy 6061 include:
Mechanical Properties:
emper |
Ultimate Tensile Strength (MPa) |
0.2% Proof Stress (MPa) |
Brinell Hardness (500kg load, 10mm ball) |
Elongation 50mm dia (%) |
0 |
110-152 |
65-110 |
30-33 |
14-16 |
T1 |
180 |
95-96 |
|
16 |
T4 |
179 min |
110 min |
|
|
T6 |
260-310 |
240-276 |
95-97 |
9-13 |
Product Details:
Material | Aluminum Alloy |
Usage/Application | Construction |
Brand | FHA |
Shape | Round |
Length | 100 m |
Form | Wire |
Packaging Type | Roll |
Grade | Al 6066 64423 H11 C62S |
Aluminium / Aluminum alloys have good corrosion resistance. They tend to lose some of their strength when subjected to high temperatures. However, their strength can be increased when exposed to subzero temperatures.
The following datasheet gives an overview of Aluminium / Aluminum 6066 alloy.
Chemical Composition:
The following table shows the chemical composition of Aluminium / Aluminum 6066 alloy.
Element |
Content (%) |
Aluminium / Aluminum, Al |
95.7 |
Silicon, Si |
1.40 |
Magnesium, Mg |
1.10 |
Copper, Cu |
1 |
Manganese, Mn |
0.8 |
Physical Properties:
Properties |
Metric |
Imperial |
Density |
2.6-2.8 g/cm3 |
0.0939- 0.101 lb/in3 |
Mechanical Properties:
The mechanical properties of Aluminium / Aluminum 6066 alloy are outlined in the following table.
Properties |
Metric |
Imperial |
Tensile strength |
150 MPa |
21755 psi |
Yield strength |
83 MPa |
12038 psi |
Shear strength |
97 MPa |
14069 psi |
Fatigue strength |
110 MPa |
15954 psi |
Elastic modulus |
70-80 GPa |
10153-11603 ksi |
Poisson's ratio |
0.33 |
0.33 |
Hardness |
43 |
43 |
Wire Gauge (SWG):
Certification:
Product Details:
Minimum Order Quantity | 50 Kilogram |
Shape | Rectangular |
Grade | 6005/6005A |
Thickness | 45 mm |
Brand | FHA |
Tolerance | -0.00mm/+5.00mm |
Material | Aluminium |
Length | 24 meter |
Aluminium alloy 6005i s a medium strength, heat treatable alloy with excellent corrosion resistance.
Alloy 6005 has properties between those of alloys 6061 and 6082 and can sometimes be used interchangeably with these alloys but 6005/6005A has better extrusion characteristics. It has a better mill surface finish, but it is difficult to produce thin-wall complicated shapes in 6005/6005A.
6005 has very good bending properties.
Chemical Composition:
Chemical composition for aluminium alloy 6005
Element |
% Present |
Si |
0.5-0.9 |
Fe |
0.0-0.35 |
Cu |
0.0-0.3 |
Mn |
0.0-0.5 |
Mg |
0.4-0.7 |
Zn |
0.0-0.2 |
Ti |
0.0-0.1 |
Cr |
0.0-0.3 |
Mn+Cr |
0.12-0.5 |
Al |
Balance |
Properties
Mechanical Properties:
Mechanical properties for aluminium alloy 6005 T6
BS EN 755-2:2008 |
|
Property |
Value |
Proof Stress |
225 Min MPa |
Tensile Strength |
270 Min MPa |
Elongation A50 mm |
8 % |
Shear Strength |
205 MPa |
Hardness Brinell |
90 HB |
Elongation A |
10 Min % |
Product Details:
Minimum Order Quantity | 50 Kilogram |
Shape | Rectangular |
Type | Plate |
Material Grade | Al 6101 63401 91E D50S E.Al.Mg.Si 0.5 |
Brand | FHA |
Tolerance | -0.00mm/+5.00mm |
Material | Aluminum Alloy |
Length | 6000 mm |
Aluminium / Aluminum alloys have good corrosion resistance. The strength of these alloys can be reduced when they are exposed to high temperatures. However, their strength can be increased at subzero temperatures. Aluminium / Aluminum 6101 alloy has good mechanical strength and high electrical conductivity.
The following datasheet will discuss in detail about Aluminium / Aluminum 6101 alloy.
The following table shows the chemical composition of Aluminium / Aluminum 6101 alloy.
Element | Content (%) |
---|---|
Aluminium / Aluminum, Al | 98.9 |
Magnesium, Mg | 0.60 |
Silicon, Si | 0.50 |
The physical properties of Aluminium / Aluminum 6101 alloy are given in the following table.
Properties | Metric | Imperial |
---|---|---|
Density | 2.7 g/cm3 | 0.0975 lb/in3 |
Melting point | 588°C | 1090°F |
The mechanical properties of Aluminium / Aluminum 6101 alloy are tabulated below.
Properties | Metric | Imperial |
---|---|---|
Tensile strength | 97 MPa | 14069 psi |
Yield strength | 76 MPa | 11023 psi |
Elastic modulus | 70-80 GPa | 10153-11603 ksi |
Poisson's ratio | 0.33 | 0.33 |
The thermal properties of Aluminium / Aluminum 6101 alloy are given in the following table.
Properties | Conditions | ||
---|---|---|---|
T (ºC) | Treatment | ||
Thermal expansion | 23 (10-6/ºC) | 20-100 | - |
Thermal conductivity | 218 W/mK | 25 | T6 |
Product Details:
Minimum Order Quantity | 50 Kilogram |
Material | Aluminum Alloy |
Usage/Application | Construction |
Brand | FHA |
Shape | Round |
Length | 500 m |
Packaging Type | Roll |
Grade | Al 8011 40800 Al-Fe-Si |
Apart from iron, aluminium / aluminum is currently the next most widely used metal in the world. This is due to the fact that aluminium / aluminum has a unique combination of attractive properties. Properties such as its low weight, corrosion resistance, and easy maintenance of final product, have ensured that this metal and its alloys will be in use for a very long time.
Aluminium / aluminum 8011 alloy is a wrought alloy. The following datasheet will provide more details about aluminium / aluminum 8011 alloy.
The following table shows the chemical composition of aluminium / aluminum 8011 alloy.
Element | Content (%) |
---|---|
Aluminum, Al | 97.3 - 98.9 |
Iron, Fe | 0.60 - 1 |
Silicon, Si | 0.50 - 0.90 |
Manganese, Mn | ≤ 0.20 |
Zinc, Zn | ≤ 0.10 |
Copper, Cu | ≤ 0.10 |
Titanium, Ti | ≤ 0.080 |
Chromium, Cr | ≤ 0.050 |
Magnesium, Mg | ≤ 0.050 |
Remainder (each) | ≤ 0.050 |
Remainder (total) | ≤ 0.15 |
Product Details:
Unit Length | 12 m |
Grade | Al 8011 |
Usage/Application | Chemical Handling |
Size/Diameter | 4 inch |
Thickness | 50 mm |
Material | Aluminum Alloys |
Shape | Round |
Surface Finish | Anodized |
Surface Finishing | Polish |
End | Plain End |
Brand | FHA |
Apart from iron, aluminium / aluminum is currently the next most widely used metal in the world. This is due to the fact that aluminium / aluminum has a unique combination of attractive properties. Properties such as its low weight, corrosion resistance, and easy maintenance of final product, have ensured that this metal and its alloys will be in use for a very long time.
Aluminium / aluminum 8011 alloy is a wrought alloy. The following datasheet will provide more details about aluminium / aluminum 8011 alloy.
The following table shows the chemical composition of aluminium / aluminum 8011 alloy.
Element | Content (%) |
---|---|
Aluminum, Al | 97.3 - 98.9 |
Iron, Fe | 0.60 - 1 |
Silicon, Si | 0.50 - 0.90 |
Manganese, Mn | ≤ 0.20 |
Zinc, Zn | ≤ 0.10 |
Copper, Cu | ≤ 0.10 |
Titanium, Ti | ≤ 0.080 |
Chromium, Cr | ≤ 0.050 |
Magnesium, Mg | ≤ 0.050 |
Remainder (each) | ≤ 0.050 |
Remainder (total) | ≤ 0.15 |