Fountainhead Alloys
Opera House, Mumbai, Maharashtra
GST No. 27AKOPC9787G1ZI
TrustSEAL Verified
Call 08047643051 89% Response Rate
SEND EMAIL
Product Details:
| Minimum Order Quantity | 50 Kilogram |
| Material | Aluminium |
| Usage/Application | Chemical Handling |
| Grade | 6066 |
| Size/Diameter | 4 inch |
| Shape | Round |
| Surface Finish | Anodized |
| End | Plain End |
| Brand | FHA |
Aluminium / Aluminum alloys have good corrosion resistance. They tend to lose some of their strength when subjected to high temperatures. However, their strength can be increased when exposed to subzero temperatures.
The following datasheet gives an overview of Aluminium / Aluminum 6066 alloy.
The following table shows the chemical composition of Aluminium / Aluminum 6066 alloy.
| Element | Content (%) |
|---|---|
| Aluminium / Aluminum, Al | 95.7 |
| Silicon, Si | 1.40 |
| Magnesium, Mg | 1.10 |
| Copper, Cu | 1 |
| Manganese, Mn | 0.8 |
| Properties | Metric | Imperial |
|---|---|---|
| Density | 2.6-2.8 g/cm3 | 0.0939- 0.101 lb/in3 |
The mechanical properties of Aluminium / Aluminum 6066 alloy are outlined in the following table.
| Properties | Metric | Imperial |
|---|---|---|
| Tensile strength | 150 MPa | 21755 psi |
| Yield strength | 83 MPa | 12038 psi |
| Shear strength | 97 MPa | 14069 psi |
| Fatigue strength | 110 MPa | 15954 psi |
| Elastic modulus | 70-80 GPa | 10153-11603 ksi |
| Poisson's ratio | 0.33 | 0.33 |
| Hardness | 43 | 43 |
Product Details:
| Minimum Order Quantity | 50 Kg |
| Material Grade | 6351 |
| Material | Aluminum Alloys |
| Size | 4 inch |
| Shape | Round |
| Surface Finish | Anodized |
| End | Plain End |
Aluminum alloys tend to lose their strength when they are exposed to temperatures of about 200-250°C. However, their strength increases at subzero temperatures. They have high corrosion resistance.
The following datasheet will discuss in detail about the aluminum 6351 alloy.
The chemical composition of the aluminum 6351 alloy is tabulated below.
| Element | Content (%) |
|---|---|
| Aluminum, Al | 97.8 |
| Silicon, Si | 1 |
| Manganese, Mn | 0.6 |
| Magnesium, Mg | 0.6 |
The following table shows the physical properties of the aluminum 6351 alloy.
| Properties | Metric | Imperial |
|---|---|---|
| Density | 2.6-2.8 g/cc | 0.0939- 0.101 lb/in3 |
The mechanical properties of the aluminum 6351 alloy are outlined in the following table.
| Properties | Metric | Imperial |
|---|---|---|
| Tensile strength | 250 MPa | 36260 psi |
| Yield strength | 150 MPa | 21756 psi |
| Shear strength | 200 MPa | 29008 psi |
| Fatigue strength | 90 MPa | 13054 psi |
| Elastic modulus | 70-80 GPa | 10153-11603 ksi |
| Poisson's ratio | 0.033 | 0.033 |
| Elongation | 20% | 20% |
| Hardness | 95 | 95 |
Product Details:
| Minimum Order Quantity | 50 Kg |
| Thickness | 5 mm |
| Grade | Al 6082 Al-Mg-Si 1 |
| Usage/Application | Construction |
| Width | 1000 mm |
| Material | Aluminum Alloys |
| Length | 6000 mm |
Aluminium alloy 6082 is a medium strength alloy with excellent corrosion resistance. It has the highest strength of the 6000 series alloys. Alloy 6082 is known as a structural alloy. In plate form, Aluminium alloy 6082is the alloy most commonly used for machining.
As a relatively new alloy, the higher strength of Aluminium alloy 6082 has seen it replace 6061 in many applications. The addition of a large amount of manganese controls the grain structure which in turn results in a stronger alloy.
In the T6 and T651 temper, Aluminium alloy 6082 machines well and produces tight coils of swarf when chip breakers are used.
Chemical Composition of Aluminium alloy 6082
Chemical composition for aluminium alloy 6082
|
Element |
% Present |
|
Si |
0.7-1.3 |
|
Fe |
0.0-0.5 |
|
Cu |
0.0-0.1 |
|
Mn |
0.4-1.0 |
|
Mg |
0.6-1.2 |
|
Zn |
0.0-0.2 |
|
Ti |
0.0-0.1 |
|
Cr |
0.0-0.25 |
|
Al |
Balance |
Properties of Aluminium alloy 6082
Mechanical properties for aluminium alloy 6082 Soft O
|
BS EN 485-2:2008 |
|
|
Property |
Value |
|
Proof Stress |
85 Max MPa |
|
Tensile Strength |
150 Max MPa |
|
Hardness Brinell |
40 HB |
Product Details:
| Minimum Order Quantity | 50 Kilogram |
| Unit Length | 12 m |
| Material | Aluminium Alloys |
| Usage/Application | Chemical Handling |
| Grade | Al 6005 62400 C51S |
| Size/Diameter | 4 inch |
| Shape | Round |
| Surface Finish | Anodized, Mill Finished, Finished Polished, Brushed |
| End | Plain End |
| Brand | FHA |
Aluminium alloy 6005i s a medium strength, heat treatable alloy with excellent corrosion resistance.
Alloy 6005 has properties between those of alloys 6061 and 6082 and can sometimes be used interchangeably with these alloys but 6005/6005A has better extrusion characteristics. It has a better mill surface finish, but it is difficult to produce thin-wall complicated shapes in 6005/6005A. 6005 has very good bending properties.
Chemical Composition:
Chemical composition for aluminium alloy 6005
|
Element |
% Present |
|
Si |
0.5-0.9 |
|
Fe |
0.0-0.35 |
|
Cu |
0.0-0.3 |
|
Mn |
0.0-0.5 |
|
Mg |
0.4-0.7 |
|
Zn |
0.0-0.2 |
|
Ti |
0.0-0.1 |
|
Cr |
0.0-0.3 |
|
Mn+Cr |
0.12-0.5 |
|
Al |
Balance |
Properties:
Mechanical Properties:
Mechanical properties for aluminium alloy 6005 T6
|
BS EN 755-2:2008 |
|
|
Property |
Value |
|
Proof Stress |
225 Min MPa |
|
Tensile Strength |
270 Min MPa |
|
Elongation A50 mm |
8 % |
|
Shear Strength |
205 MPa |
|
Hardness Brinell |
90 HB |
|
Elongation A |
10 Min % |
Product Details:
| Minimum Order Quantity | 50 Kg |
| Material | Aluminum Alloy |
| Grade | Al 6082 Al-Mg-Si 1 |
| Single Piece Length | 6 meter |
| Brand | FHA |
| Usage/Application | Construction |
| Diameter | 500 mm |
| Shape | Round |
Aluminium alloy 6082 is a medium strength alloy with excellent corrosion resistance. It has the highest strength of the 6000 series alloys. Alloy 6082 is known as a structural alloy. In plate form, Aluminium alloy 6082is the alloy most commonly used for machining.
As a relatively new alloy, the higher strength of Aluminium alloy 6082 has seen it replace 6061 in many applications. The addition of a large amount of manganese controls the grain structure which in turn results in a stronger alloy.
In the T6 and T651 temper, Aluminium alloy 6082 machines well and produces tight coils of swarf when chip breakers are used.
Chemical Composition of Aluminium alloy 6082
|
Element |
% Present |
|
Si |
0.7-1.3 |
|
Fe |
0.0-0.5 |
|
Cu |
0.0-0.1 |
|
Mn |
0.4-1.0 |
|
Mg |
0.6-1.2 |
|
Zn |
0.0-0.2 |
|
Ti |
0.0-0.1 |
|
Cr |
0.0-0.25 |
|
Al |
Balance |
Mechanical Properties of Aluminium alloy 6082
|
BS EN 485-2:2008 |
|
|
Property |
Value |
|
Proof Stress |
85 Max MPa |
|
Tensile Strength |
150 Max MPa |
|
Hardness Brinell |
40 HB |
Product Details:
| Minimum Order Quantity | 50 Kilogram |
| Unit Length | 12 m |
| Material | Aluminium Alloys |
| Usage/Application | Chemical Handling |
| Grade | Al 6082 Al-Mg-Si 1 |
| Shape | Round |
| Size | 4" |
| Surface Finish | Finished Polished, Brushed, Anodized, Mill Finished |
| End | Plain End |
| Brand | FHA |
Aluminium alloy 6082 is a medium strength alloy with excellent corrosion resistance. It has the highest strength of the 6000 series alloys. Alloy 6082 is known as a structural alloy. In plate form, Aluminium alloy 6082is the alloy most commonly used for machining.
As a relatively new alloy, the higher strength of Aluminium alloy 6082 has seen it replace 6061 in many applications. The addition of a large amount of manganese controls the grain structure which in turn results in a stronger alloy.
In the T6 and T651 temper, Aluminium alloy 6082 machines well and produces tight coils of swarf when chip breakers are used.
Chemical Composition of Aluminium alloy 6082
Chemical composition for aluminium alloy 6082
|
Element |
% Present |
|
Si |
0.7-1.3 |
|
Fe |
0.0-0.5 |
|
Cu |
0.0-0.1 |
|
Mn |
0.4-1.0 |
|
Mg |
0.6-1.2 |
|
Zn |
0.0-0.2 |
|
Ti |
0.0-0.1 |
|
Cr |
0.0-0.25 |
|
Al |
Balance |
Properties of Aluminium alloy 6082
Mechanical properties for aluminium alloy 6082 Soft O
|
BS EN 485-2:2008 |
|
|
Property |
Value |
|
Proof Stress |
85 Max MPa |
|
Tensile Strength |
150 Max MPa |
|
Hardness Brinell |
40 HB |